Thursday, November 16, 2017

New Liquid Fuels Including Gasoline, Diesel, Kerosene, Etc. Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Liquid Fuels Including Gasoline, Diesel, Kerosene, Etc. are now available:

  • ASTM D1655, 2017 Edition, Standard Specification for Aviation Turbine Fuels
  • ASTM D3242, 2011 Edition Reapproved in 2017, Standard Test Method for Acidity in Aviation Turbine Fuel
  • ASTM D381, 2012 Edition Reapproved in 20107, Standard Test Method for Gum Content in Fuels by Jet Evaporation
  • ASTM D3813, 2012 Edition Reapproved in 2017, Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy
  • ASTM D396, 2017 Edition, Standard Specification for Fuel Oils
  • ASTM D4806, 2017 Edition, Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel   
  • ASTM D5773, 2017 Edition with an Editorial Correction (E1), Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Constant Cooling Rate Method)
  • ASTM D5798, 2017 Edition, Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines 
  • ASTM D613, 2017B Edition, Standard Test Method for Cetane Number of Diesel Fuel Oil
  • ASTM D6584, 2017 Edition, Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography 
  • ASTM D7185, 2017 Edition, Standard Specification for Low Toluene Low Dioxane (LTLD) Benzene
  • ASTM D7220, 2012 Edition Reapproved in 2017, Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry
  • ASTM D7223,  2017 Edition, Standard Specification for Aviation Certification Turbine Fuel
  • ASTM D7547, 2017A Edition, Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
  • ASTM D7566, 2017A Edition, Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
  • ASTM D7591, 2012 Edition Reapproved in 2017, Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography
  • ASTM D7618, 2013 Edition Reapproved in 2017, Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel
  • ASTM D7619, 2017 Edition, Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter
  • ASTM D7717, 2011 Edition Reapproved in 2017, Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis
  • ASTM D7757, 2017 Edition, Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
  • ASTM D7923, 2017A Edition, Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration
  • ASTM D8049, 2017 Edition, Standard Test Method for Determining Concentration, Count, and Size Distribution of Solid Particles and Water in Light and Middle Distillate Fuels by Direct Imaging Particle Analyzer
  • ASTM D8076, 2017A Edition, Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
  • BS 2869, 2017 Edition, Fuel oils for agricultural, domestic and industrial engines and boilers. Specification
  • BS EN 1601, 2017 Edition, Liquid petroleum products. Determination of organic oxygenate compounds and total organically bound oxygen content in unleaded petrol. Method by gas chromatography (O-FID)    
  • BS EN 16906, 2017 Edition, Liquid petroleum products. Determination of the ignition quality of diesel fuels. BASF engine method      
  • BS EN 16934, 2017 Edition, Automotive fuels and fat and oil derivates, Determination of steryl glycosides in fatty acid methyl esters (FAME). Method by GC-MS with prior purification by SPE
  • BS EN 16942, 2016 Edition, Fuels. Identification of vehicle compatibility. Graphical expression for consumer information
  • BS EN 16997, 2017 Edition, Liquid petroleum products. Determination of the sulfur content in Ethanol (E85) automotive fuel. Wavelength dispersive X-ray fluorescence spectrometric method
  • BS EN ISO 6246, 2017 Edition, Petroleum products. Gum content of fuels. Jet evaporation method
  • BS ISO 12156-2, 2017 Edition, Petroleum products. Gum content of fuels. Jet evaporation method
  • DIN EN 590, 2017 Edition, Automotive fuels - Diesel - Requirements and test methods  
  • ISO 12156-2, 3rd Edition, Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Part 2: Limit
  • PD CEN 16389, 2017 Edition, Automotive fuels. Paraffinic diesel fuel and blends with FAME. Background to the parameters required and their respective limits and determination
  • ASTM D473, 2007 Edition Reapproved in 2017 with an Editorial Correction (E1), Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method  

Fore more standards like these, please refer to our Document Center List of Liquid Fuels Including gasoline, Diesel, Kerosene, Etc. Standards

Friday, November 10, 2017

New Concrete and Concrete Products Including Admixtures Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Concrete and Concrete Products Including Admixtures are now available:


  • ASTM C1202, 2017 Edition, Standard Test Method for Electrical Indication of Concrete's Ability to Resist Chloride Ion Penetration
  • ASTM C129, 2017 Edition, Standard Specification for Nonloadbearing Concrete Masonry Units
  • ASTM C1319, 2017 Edition, Standard Specification for Concrete Grid Paving Units
  • ASTM C139, 2017 Edition, Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
  • ASTM C140, 2017A Edition, Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
  • ASTM C156, 2017 Edition, Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete
  • ASTM C1610, 2017 Edition, Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column Technique
  • ASTM C1621, 2017 Edition, Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring
  • ASTM C1623, 2017A Edition, Standard Specification for Manufactured Concrete Masonry Lintels
  • ASTM C1634, 2017 Edition, Standard Specification for Concrete Facing Brick
  • ASTM C1677, 2011A Reapproved in 2017, Standard Specification for Joints for Concrete Box, Using Rubber Gaskets
  • ASTM C1686, 2009 Edition Reapproved in 2017, Standard Practice for Installation and Testing of Reinforced Autoclaved Aerated Concrete (AAC) Units
  • ASTM C1693, 2011 Edition Reapproved in 2017, Standard Specification for Autoclaved Aerated Concrete (AAC)   
  • ASTM C1694, 2009 Reapproved in 2017, Standard Specification for Reinforced Autoclaved Aerated Concrete (AAC) Elements
  • ASTM C1712, 20107 Edition, Standard Test Method for Rapid Assessment of Static Segregation Resistance of Self-Consolidating Concrete Using Penetration Test
  • ASTM C1719, 2011 Reapproved in 2017, Standard Test Method for Installed Precast Concrete Tanks and Accessories by the Negative Air Pressure (Vacuum) Test Prior to Backfill
  • ASTM C174, 2017 Edition, Standard Test Method for Measuring Thickness of Concrete Elements Using Drilled Concrete Cores
  • ASTM C1761, 2017 Edition, Standard Specification for Lightweight Aggregate for Internal Curing of Concrete
  • ASTM C31, 2017 Edition, Standard Practice for Making and Curing Concrete Test Specimens in the Field
  • ASTM C330, 2017A Edition, Standard Specification for Lightweight Aggregates for Structural Concrete    
  • ASTM C331, 2017 Edition, Standard Specification for Lightweight Aggregates for Concrete Masonry Units
  • ASTM C332, 2017 Edition, Standard Specification for Lightweight Aggregates for Insulating Concrete
  • ASTM C39, 2017B Edition, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
  • ASTM C494, 2017 Edition, Standard Specification for Chemical Admixtures for Concrete
  • ASTM C55, 2017 Edition, Standard Specification for Concrete Building Brick
  • ASTM C641, 2017 Edition, Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates
  • ASTM C823, 2012 Edition Reapproved in 2017, Standard Practice for Examination and Sampling of Hardened Concrete in Constructions
  • ASTM C94, 2017A Edition, Standard Specification for Ready-Mixed Concrete
  • BS EN 16757, 2017 Edition, Sustainability of construction works. Environmental product declarations. Product Category Rules for concrete and concrete elements
  • ISO 19595, 1st Edition, Natural aggregates for concrete
  • JIS A 1118, 2017 Edition, Natural aggregates for concrete
  • JIS A 6207, 2016 Edition, Silica fume for use in concrete


For more standards like these, please refer to our Document Center List of Concrete and Concrete Products Including Admixtures Standards.        

Wednesday, November 8, 2017

New Testing of Metals Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Testing of Metals are now available:


  • ASTM A956, 2017 Edition, Standard Test Method for Leeb Hardness Testing of Steel Products
  • ASTM E18, 2017 Edition with Editorial Correction (E1), Standard Test Methods for Rockwell Hardness of Metallic Materials
  • ASTM E1820, 2017 Edition, Standard Test Method for Measurement of Fracture Toughness
  • ASTM E2492, Withdrawn with no replacement, Standard Test Method for Evaluating Springback of Sheet Metal Using the Demeri Split Ring Test (Withdrawn 2017)
  • BS EN ISO 377, 2017 Edition, Steel and steel products. Location and preparation of samples and test pieces for mechanical testing
  • BS ISO 15363, 2017 Edition, Metallic materials. Tube ring hydraulic pressure test
  • ISO 15363, 2nd Edition, Metallic materials - Tube ring hydraulic pressure test
  • JIS B 7726, 2017 Edition, Rockwell hardness test - Verification and calibration of testing machines and indenters
  • JIS B 7730, 2017 Edition, Rockwell hardness test - Calibration of reference blocks
  • ASTM E94, 2017 Edition, Standard Guide for Radiographic Examination Using Industrial Radiographic Film
  • ASTM E2626, Withdrawn with no replacement, Standard Guide for Spectrometric Analysis of Reactive and Refractory Metals (Withdrawn 2017)
  • ASTM E34, Withdrawn and replaced by ASTM E3061, Standard Test Methods for Chemical Analysis of Alloys, Aluminum and Aluminum Base
  • ASTM E439, 2017 Edition, Standard Test Methods for Chemical Analysis of Beryllium
  • ASTM E55, 2011 Edition Reapproved in 2017, Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
  • ASTM E581, 2017 Edition, Standard Test Methods for Chemical Analysis of Manganese-Copper Alloys
  • ASTM E88, 2011 Edition Reapproved in 2017, Standard Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
  • JIS G 0321, 2017 Edition, Product analysis and its tolerance for wrought steel   
  • ASTM E432, 1991 Edition Reapproved in 2017 with an Editorial Correction (E1), Standard Guide for Selection of a Leak Testing Method
  • BS EN 10247, 2017 Edition, Micrographic examination of the non-metallic inclusion content of steels using standard pictures
  • ASTM E7, 2017 Edition, Standard Terminology Relating to Metallography


For more standards like these, please refer to our Document Center List of Testing Metals Standards.  

Tuesday, November 7, 2017

New Acoustics and Acoustic Measurements Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Acoustics and Acoustic Measurement are now available:


  • ASTM E1106, 2012 Edition Reapproved in 2017, Standard Test Method for Primary Calibration of Acoustic Emission Sensors
  • ASTM E1139, 2017 Edition, Standard Practice for Continuous Monitoring of Acoustic Emission from Metal Pressure Boundaries
  • ASTM E1211, 2017 Edition, Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors
  • ASTM E1932, 2012 Edition Reapproved in 2017, Standard Guide for Acoustic Emission Examination of Small Parts
  • ASTM E2611, 2017 Edition, Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method
  • ASTM E650, 2017 Edition, Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors
  • BS ISO 26101, 2017 Edition, Acoustics. Test methods for the qualification of free-field environments
  • BS ISO 532-2, 2017 Edition, Acoustics. Methods for calculating loudness. Moore-Glasberg method
  • ISO 1996-2, 3rd Edition, Acoustics - Description, measurement and assessment of environmental noise - Part 2: Determination of sound pressure levels
  • ISO 532-2, 1st Edition, Acoustics - Methods for calculating loudness - Part 2: Moore-Glasberg method
  • ASTM E1888, 2017 Edition, Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
  • ASTM E2863, 2017 Edition, Standard Practice for Acoustic Emission Examination of Welded Steel Sphere Pressure Vessels Using Thermal Pressurization
  • ASTM E749, 2017 Edition, Standard Practice for Acoustic Emission Monitoring During Continuous Welding
  • ASTM E751, 2017 Edition, Standard Practice for Acoustic Emission Monitoring During Resistance Spot-Welding
  • BS 7135-3, Withdrawn and replaced by BS ISO 9296, Noise emitted by computer and business equipment. Method for determining and verifying declared noise emission values
  • BS ISO 9296, 2017 Edition, Acoustics. Declared noise emission values of information technology and telecommunications equipment
  • ISO 9296, 2nd Edition, Acoustics - Declared noise emission values of information technology and telecommunications equipment
  • BS 5653, Withdrawn and replaced by BS EN 60500, Specification for hydrophones for calibration purposes
  • BS EN 60500, 2017 Edition, Underwater acoustics. Hydrophones. Properties of hydrophones in the frequency range 1 Hz to 500 kHz
  • IEC 61391-1-AM1, Amendment 1 for Edition 1.10, Amendment 1 - Ultrasonics - Pulse-echo scanners - Part 1: Techniques for calibrating spatial measurement systems and measurement of point-spread function response
  • PD IEC 63079, 2017 Edition, Code of practice for hearing-loop systems (HLS)
  • IEC 62462, Edition 2.0, Ultrasonics - Output test - Guidance for the maintenance of ultrasound physiotherapy systems


For more standards like these, please refer to our Document Center List of Acoustics and Acoustic Measurements Standards.

Thursday, November 2, 2017

New Road Construction Materials Including Asphalts, Road Pavements, Etc. Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Road Construction Materials Including Asphalts, Road Pavements, Etc. are now available:


  • ASTM C1272, 2017 Edition, Standard Specification for Heavy Vehicular Paving Brick
  • ASTM C1782, 2017 Edition, Standard Specification for Utility Segmental Concrete Paving Slabs
  • ASTM D4796, 2017 Edition, Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials
  • ASTM D6931, 2017 Edition, Standard Test Method for Indirect Tensile (IDT) Strength of Asphalt Mixtures
  • ASTM D6936, 2017 Edition, Standard Test Method for Determining Demulsibility of Emulsified Asphalt
  • BS 594987, Amendment 1 (A1) for 2015 Edition, Asphalt for roads and other paved areas. Specification for transport, laying, compaction and product type testing protocols
  • BS EN 12697-18, 2017 Edition, Bituminous mixtures. Test methods. Binder drainage 
  • BS EN 12697-27, 2017 Edition, Bituminous mixtures. Test methods. Sampling
  • BS EN 13286-43, 2003 Edition, Unbound and hydraulically bound mixtures. Test method for the determination of the modulus of elasticity of hydraulically bound mixtures
  • BS EN 14187-1, 2017 Edition, Cold applied joint sealants. Test methods. Determination of rate of cure
  • DIN EN 14187-2, 2017 Edition, Cold applied joint sealants - Test methods - Part 2: Determination of tack free time
  • DIN EN 14187-3, 2017 Edition, Cold applied joint sealants - Test methods - Part 3: Determination of self-levelling properties
  • DIN EN 14187-4, 2017 Edition, Cold applied joint sealants - Test methods - Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals
  • DIN EN 14187-6, 2017 Edition, Cold applied joint sealants - Test method - Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals
  • DIN EN 14187-8, 2017 Edition, Cold applied joint sealants - Test methods - Part 8: Determination of the artificial weathering by UV-irradiation
  • PD CEN 12697-51, 2017 Edition, Bituminous mixtures. Test methods. Surface shear strength test
  • PD CEN 12697-52, 2017 Edition, Bituminous mixtures. Test methods. Conditioning to address oxidative ageing
  • ASTM E1170, 1997 Edition Reapproved in 2017, Standard Practices for Simulating Vehicular Response to Longitudinal Profiles of Traveled Surfaces
  • ASTM E1783, 1996 Edition Reapproved in 2017, Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures
  • ASTM D4799, 2017 Edition, Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)


For more standards like these, please refer to our Document Center List of Road Construction Materials Including Asphalts, Road Pavements, Etc. Standards.           

Monday, October 30, 2017

New Products of the Chemical Industry Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Products of the Chemical Industry are now available:


  • ISO 10156, 4th Edition, Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets
  • ASTM E1754, 2017A Edition, Standard Test Method for Determination of Low Levels of Water in Liquid Chlorine By Infrared Spectrophotometry
  • ASTM E1786, 2017A Edition, Standard Test Method for Determination of Low Levels of Water in Liquid Chlorine by On-Line Infrared Spectrophotometry
  • BS EN ISO 10156, 2017 Edtion, Gas cylinders. Gases and gas mixtures. Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets
  • BS ISO 13338, 2017 Edition, Gas cylinders. Gases and gas mixtures. Determination of tissue corrosiveness for the selection of cylinder valve outlets
  • BS EN 15947-4, Corrigendum 1 (C1) for 2015 Edition, Pyrotechnic articles. Fireworks, Categories F1, F2 and F3. Test methods
  • ASTM D1782, 2017 Edition, Standard Test Methods for Operating Performance of Particulate Cation-Exchange Materials
  • ASTM D2187, 2017 Edition, Standard Test Methods and Practices for Evaluating Physical and Chemical Properties of Particulate Ion-Exchange Resins
  • ASTM D4456, 2017 Edition, Standard Test Methods for Physical and Chemical Properties of Powdered Ion Exchange Resins
  • ASTM D7513, 2017 Edition, Standard Test Method for Capacity of Mixed Bed Ion Exchange Cartridges
  • BS ISO 16128-2, 2017 Edition, Cosmetics. Guidelines on technical definitions and criteria for natural and organic cosmetic ingredients. Criteria for ingredients and products
  • ISO 16128-2, 1st Edition, Cosmetics - Guidelines on technical definitions and criteria for natural and organic cosmetic ingredients - Part 2: Criteria for ingredients and products
  • ISO 18818, 1st Edition, Cosmetics - Analytical method - Detection and quantitative determination of Diethanolamine (DEA) by GC/MS
  • PD ISO 18818, 2017 Edition, Cosmetics. Analytical method. Detection and quantitative determination of Diethanolamine (DEA) by GC/MS
  • BS EN ISO 11609, 2017 Edition, Dentistry. Dentifrices. Requirements, test methods and marking
  • BS EN ISO 21148, 2017 Edition, Cosmetics. Microbiology. General instructions for microbiological examination
  • BS EN ISO 21149, 2017 Edition, Cosmetics. Microbiology. Enumeration and detection of aerobic mesophilic bacteria
  • BS EN ISO 18415, 2017 Edition, Cosmetics. Microbiology. Detection of specified and non-specified microorganisms
  • BS EN 12485, 2017 Edition, Chemicals used for treatment of water intended for human consumption. Calcium carbonate, high-calcium lime, half-burnt dolomite, magnesium oxide, calcium magnesium carbonate and dolomitic lime. Test methods  
  • ASTM E299, 2017A Edition, Standard Test Method for Trace Amounts of Peroxides In Organic Solvents


For more standards like these, please refer to our Document Center List of Products of the Chemical Industry Standards.            

Friday, October 27, 2017

New Protective Equipment Occupational Safety Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Protective Equipment Occupational Safety are now available:


  • ASTM D1937, 2004 Edition Reapproved in 2017, Standard Specification for Body Protectors Used in Horse Sports and Horseback Riding
  • ASTM F2733, 20107 Edition, Standard Specification for Flame-Resistant Rainwear for Protection Against Flame Hazards
  • BS EN 13911, 2017 Edition, Protective clothing for firefighters. Requirements and test methods for fire hoods for firefighters
  • BS EN ISO 13506-1, 2017 Edition, Protective clothing against heat and flame. Test method for complete garments. Measurement of transferred energy using an instrumented manikin
  • BS ISO 13506, Withdrawn and replaced by BS ISO 13506-2 & BS EN ISO 13506-1, Protective clothing against heat and flame. Test method for complete garments. Prediction of burn injury using an instrumented manikin
  • BS ISO 13506-1, 2017 Edition, Protective clothing against heat and flame. Skin burn injury prediction. Calculation requirements and test cases
  • DD 7971-9, Withdrawn with no replacement, Protective clothing and equipment for use in violent situations and in training. Training suits and equipment. Requirements and test methods
  • ISO 13506, Withdrawn and replaced by ISO 13506-1 & ISO 13506-2, Protective clothing against heat and flame - Test method for complete garments - Prediction of burn injury using an instrumented manikin
  • ISO 13506-1, 1st Edition, Protective clothing against heat and flame - Part 1: Test method for complete garments - Measurement of transferred energy using an instrumented manikin  
  • ISO 13506-2, 1st Edition, Protective clothing against heat and flame - Part 2: Skin burn injury prediction - Calculation requirements and test cases
  • ASTM F1670, 2017 Edition, Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood
  • ASTM F2178, 2017A Edition, Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products
  • BS EN 1384, 2017 Edition, Helmets for equestrian activities
  • BS ISO 10256-5, 2017 Edition, Protective equipment for use in ice hockey. Part 5: Neck laceration protectors for ice hockey players
  • DD 253, Withdrawn with no replacement, Mouthguards for use in sport and recreation. Requirements and test methods
  • BS EN 13911, 2017 Edition, Protective clothing for firefighters. Requirements and test methods for fire hoods for firefighters
  • ASTM F2704, 2017 Edition, Standard Specification for Air-Fed Protective Ensembles
  • BS EN ISO 20349, Withdrawn and replaced by BS EN ISO 20349-2,  Personal protective equipment. Footwear protecting against thermal risks and molten metal splashes as found in foundries and welding. Requirements and test method
  • BS EN ISO 20349-2, 2017 Edition, Personal protective equipment - Footwear protecting against risks in foundries and welding. Part 2: Requirements and test methods for protection against risks in welding and allied processes
  • ISO 20349-1, 1st Edition, Personal protective equipment - Footwear protecting against risks in foundries and welding - Part 1: Requirements and test methods for protection against risks in foundries
  • ISO 20349-2, 1st Edition, Personal protective equipment - Footwear protecting against risks in foundries and welding - Part 1: Requirements and test methods for protection against risks in foundries


For more standards like these, please refer to our Document Center List of Protective Equipment Occupational Safety Standards

Thursday, October 26, 2017

New IT Applications in Transport and Trade Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on IT Applications in Transport and Trade are now available:


  • BS ISO 24097-1, 2017 Edition, Intelligent transport systems. Using web services (machine-machine delivery) for ITS service delivery. Realization of interoperable web services
  • DD CEN ISO 14823, Withdrawn and replaced by BS EN ISO 14823, Traffic and travel information. Messages via media independent stationary dissemination systems. Graphic data dictionary for pre-trip and in-trip information dissemination systems
  • ISO 18317, 1st Edition, Intelligent transport systems - Pre-emption of ITS communication networks for disaster and emergency communication - Use case scenarios
  • ISO 24097-1, 2nd Edition, Intelligent transport systems - Using web services (machine-machine delivery) for ITS service delivery - Part 1: Realization of interoperable web services
  • PD ISO 18317, 2017 Edition, Intelligent transport systems. Pre-emption of ITS communication networks for disaster and emergency communication. Use case scenarios
  • BS EN 50657, 2017 Edition, Railways Applications. Rolling stock applications. Software on Board Rolling Stock
  • BS ISO 13111-1, 2017 Edition, Intelligent transport systems (ITS). The use of personal ITS station to support ITS service provision for travellers. General information and use case definitions
  • BS ISO 14817-3, 2017 Edition, Intelligent transport systems. ITS data dictionaries. Object identifier assignments for ITS data concepts     
  • BS ISO 15638-10, 2017 Edition, Intelligent transport systems. Framework for cooperative telematics applications for regulated commercial freight vehicles (TARV). Emergency messaging system/eCall
  • BS ISO 15638-18, 2017 Edition, Intelligent transport systems. Framework for cooperative telematics applications for regulated commercial freight vehicles (TARV). ADR (Dangerous Goods)
  • BS ISO 17361, 2017 Edition, Intelligent transport systems. Lane departure warning systems. Performance requirements and test procedures
  • ISO 14817-3, 1st Edition, Intelligent transport systems - ITS data dictionaries - Part 3: Object identifier assignments for ITS data concepts
  • ISO 17444-1, 2nd Edition, Electronic fee collection - Charging performance - Part 1: Metrics
  • ISO 17444-2, 2nd Edition, Electronic fee collection - Charging performance - Part 2: Examination framework
  • ISO 20526, 1st Edition, Account-based ticketing state of the art report
  • ISO 20545, 1st Edition, Intelligent transport systems - Vehicle/roadway warning and control systems - Report on standardisation for vehicle automated driving systems (RoVAS)/Beyond driver assistance systems
  • PD CEN 16794-1, 2017 Edition, Public transport. Communication between contactless readers and fare media. Implementation requirements for ISO/IEC 14443
  • PD ISO 15638-10, Withdrawn and replaced by BS ISO 15638-10, Intelligent transport systems. Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV). Emergency messaging system/eCall (EMS)
  • PD ISO 20026, 2017 Edition, Intelligent transport systems. Cooperative ITS. Test architecture
  • PD ISO 20526, 2017 Edition, Account-based ticketing state of the art report
  • PD ISO 20545, 2017 Edition, Intelligent transport systems. Vehicle/roadway warning and control systems. Report on standardisation for vehicle automated driving systems (RoVAS)/Beyond driver assistance systems
  • PD ISO 21219-22, 2017 Edition, Intelligent transport systems. Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2). OpenLR location referencing (TPEG2-OLR)
  • PD ISO 21219-7, 2017 Edition, Intelligent transport systems. Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2). Location referencing container (TPEG2-LRC)


For more standards like these, please refer to our Document Center List of IT Applications in Transport and Trade Standards.        

Tuesday, October 24, 2017

New Insulating Materials Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Insulating Materials are now available:


  • IEC 60811-201-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 201: General tests - Measurement of insulation thickness
  • IEC 60811-202-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 202: General tests - Measurement of thickness of non-metallic sheath
  • IEC 60811-401-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 401: Miscellaneous tests - Thermal ageing methods - Ageing in an air oven
  • IEC 60811-508-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 508: Mechanical tests - Pressure test at high temperature for insulation and sheaths
  • IEC 60811-509-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 509: Mechanical tests - Test for resistance of insulations and sheaths to cracking (heat shock test)
  • IEC 60811-511-AM1, Amendment 1 for Edition 1.0, Amendment 1 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 511: Mechanical tests - Measurement of the melt flow index of polyethylene and polypropylene compounds
  • IEC 60893-3-6-AM2, Amendment 2 for Edition 2.0, Amendment 2 - Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-6: Specifications for individual materials - Requirements for rigid laminated sheets based on silicone resins
  • IEC 60893-4-AM1, Amendment 1 for Edition 2.0, Amendment 1 - Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 4: Typical values
  • PD IEC 60493-3, 2017 Edition, Guidelines for the statistical analysis of ageing test data. Minimum specimen numbers at different test conditions with given experimental data
  • JIS C 2136, Refer to JIS C 2136 Japanese for 2017 Edition, Test method for evaluating resistance to tracking and erosion of electrical insulating materials used under severe ambient conditions
  • ASTM D1000, 2017 Edition, Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
  • ASTM D2522, Withdrawn with no replacement, Standard Test Method for Chlorine Content of Polybutenes Used for Electrical Insulation (Withdrawn 2017)
  • ASTM D4314, Withdrawn with no replacement, Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets For Wire and Cable (Withdrawn 2017)
  • ASTM D7793, 2017 Edition, Standard Specification for Insulated Vinyl Siding
  • ASTM D790, 2017 Edition, Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
  • BS EN 60674-3-8, Amendment 1 for 2011 Edition, Plastic films for electrical purposes. Specifications for individual materials. Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation
  • BS EN 60674-2, 2017 Edition, Specification for plastic films for electrical purposes. Methods of test
  • ASTM D2100, 1995 Edition Reapproved in 2017, Standard Specification for Asbestos Textiles Used for Electrical Insulating Purposes
  • BS 1858, Withdrawn with no replacement, Electric cables. Accessories. Bitumen-based filling compounds


For more standards like these, please refer to our Document Center List of Insulating Materials Standards.   

Monday, October 23, 2017

New Raw Materials for Rubber and Plastics Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Raw Materials for Rubber and Plastics are now available:


  • BS ISO 20299-2, 2017 Edition, Film for wrapping rubber bales. Natural rubber
  • ISO 20299-2, 2nd Edition, Film for wrapping rubber bales - Part 2: Natural rubber
  • BS ISO 10638, 2017 Edition, Rubber. Identification of antidegradants by gas chromatography/mass spectrometry
  • BS ISO 1795, 2017 Edition, Rubber, raw natural and raw synthetic. Sampling and further preparative procedures
  • BS ISO 19846, 2017 Edition, Reclaimed rubber. Coding and classification system
  • BS ISO 20851, 2017 Edition, Synthetic rubber latex. Examination for microorganisms
  • BS ISO 22768, 2017 Edition, Rubber, raw. Determination of the glass transition temperature by differential scanning calorimetry (DSC)
  • BS ISO 2930, 2017 Edition, Rubber, raw natural. Determination of plasticity retention index (PRI)
  • ISO 1795, 5th Edition, Rubber, raw natural and raw synthetic - Sampling and further preparative procedures
  • ISO 20851, 1st Edition, Synthetic rubber latex - Examination for microorganisms
  • ISO 22768, 2nd Edition, Rubber, raw - Determination of the glass transition temperature by differential scanning calorimetry (DSC)
  • ISO 2930, 5th Edition, Rubber, raw natural - Determination of plasticity retention index (PRI)
  • ISO 10638, 2nd Edition, Rubber - Identification of antidegradants by gas chromatography/mass spectrometry
  • ASTM D1618, 2017 Edition, Standard Test Method for Carbon Black Extractables - Transmittance of Toluene Extract
  • ASTM D1992, 2017 Edition, Standard Guide for Testing Synthetic Plasticizers Used in Rubber
  • ASTM D3265, 2017A Edition, Standard Test Method for Carbon Black - Tint Strength
  • ASTM D4934, 2002 Edition Reapproved in 2017, Standard Test Method for Rubber Compounding Materials: 2-Benzothiazyl Sulfenamide Accelerators-Insolubles
  • ASTM D5376, 2006 Edition Reapproved in 2017, Standard Test Method for Rubber Compounding Materials - Determination of the Basic Nitrogen Content in Rubber Antioxidant: Polymerized TMQ
  • ASTM D5460, 2002 Edition Reapproved in 2017, Standard Test Method for Rubber Compounding Materials - Water in Rubber Additives
  • ASTM D5461, 2006 Edition Reapproved in 2017, Standard Test Method for Rubber Compounding Materials - Wet Sieve Analysis of Powdered Rubber Compounding Materials
  • ASTM D6915, 2017 Edition with an Editorial Correction (E1), Standard Practice for Carbon Black - Evaluation of Standard Reference Blacks
  • ISO 10638, 2nd Edition, Rubber - Identification of antidegradants by gas chromatography/mass spectrometry     
  • ISO 11236, 2nd Edition, Rubber compounding ingredients - p-Phenylenediamine antidegradants (PPDs) - Test methods
  • BS ISO 10638, 2017 Edition, Rubber. Identification of antidegradants by gas chromatography/mass spectrometry
  • BS ISO 11236, 2017 Edition, Rubber compounding ingredients. p-Phenylenediamine antidegradants (PPDs). Test methods
  • BS ISO 6472, 2017 Edition, Rubber compounding ingredients. Abbreviated terms
  • ISO 6472, 5th Edition, Rubber compounding ingredients - Abbreviated terms


For more standards like these,  please refer to our Document Center List of Raw Materials for Rubber and Plastics Standards.               

Friday, October 20, 2017

New Plastic Pipes Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Plastic Pipes are now available:


  • ASTM D2310, Withdrawn with no replacement, Standard Classification for Machine-Made 'Fiberglass' (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe (Withdrawn 2017)
  • ASTM D2846, 2017A Edition, Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems
  • ASTM D2924, 2012 Edition Reapproved in 2017, Standard Test Method for External Pressure Resistance of 'Fiberglass' (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
  • ASTM D2996, 2017 Edition, Standard Specification for Filament-Wound 'Fiberglass' (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
  • ASTM F1281, 2017 Edition, Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe
  • ASTM F2390, 2012 Edition Reapproved in 2017, Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
  • ASTM F2737, 2011 Edition Reapproved in 2017, Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units
  • ASTM F2830, 2011 Edition Reaprroved in 2017, Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
  • ASTM F2896, 2011 Edition Reapproved in 2017, Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
  • ASTM F2986, 2012 Edition Reapproved in 2017, Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications
  • ASTM F412, 2017A Edition, Standard Terminology Relating to Plastic Piping Systems
  • BS ISO 12176-1, 2017 Edition, Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems. Butt fusion
  • BS ISO 13761, 2017 Edition, Plastics pipes and fittings. Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 °C
  • BS ISO 7510, 2017 Edition, Plastics piping systems. Glass-reinforced plastics (GRP) components. Determination of the amounts of constituents
  • DIN EN ISO 15876-2, 2017 Edition, Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes
  • ISO 12512, 1st Edition, Glass reinforced thermosetting plastic (GRP) pipes - Determination of initial specific ring stiffness using segment test species cut from a pipe
  • ISO 13260, 1st Edition, Thermoplastics piping systems for non-pressure underground drainage and sewerage -- Test method for resistance to combined temperature cycling and external loading
  • ISO 13761, 2nd Edition, Plastics pipes and fittings - Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C
  • ISO 7510, 2nd Edition, Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents
  • PD ISO 12512, 2017 Edition, Glass reinforced thermosetting plastic (GRP) pipes. Determination of initial specific ring stiffness using segment test species cut from a pipe
  • PD ISO 20656-1, 2017 Edition, Plastics piping systems. General rules for structural design of glass-reinforced thermosetting plastics (GRP) pipes. Buried pipes
  • ASTM  F1675, 2013 Edition Reapproved in 2017, Standard Practice for Life-Cycle Cost Analysis of Plastic Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits
  • ISO 12176-1, 4th Edition, Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1: Butt fusion
  • ISO 13260-AM1, Amendment 1 for 1st Edition, AMENDMENT 1, Thermoplastics piping systems for non-pressure underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading         



For more standards like these, please refer to our Document Center List of Plastic Pipes Standards. 

Thursday, October 19, 2017

New Implants for Surgery Standards for the 3rd Quarter 2017

Document Center Inc. is pleased to announce that the following New Standards on Implants for Surgery are now available:


  • AAMI/ISO 25539-1, 2017 Edition, Cardiovascular implants - Endovascular devices - Part 1: Endovascular prostheses
  • ANSI/AAMI/ISO 255391, Please refer to AAMI/ISO 25539-1, Cardiovascular implants - Endovascular devices - Part 1: Endovascular prostheses
  • ASTM F1538, 2003 Edition Reapproved in 2017, Standard Specification for Glass and Glass Ceramic Biomaterials for Implantation
  • ASTM F1634, Withdrawn with no replacement, Standard Practice for In-Vitro Environmental Conditioning of Polymer Matrix Composite Materials and Implant Devices
  • ASTM F1831, 2017 Edition, Standard Specification for Cranial Traction Tongs and Halo External Spinal Immobilization Devices
  • ASTM F2102, 2017 Edition, Standard Guide for Evaluating the Extent of Oxidation in Polyethylene Fabricated Forms Intended for Surgical Implants
  • ASTM F2581, 2012 Edition Reapproved in 2017, Standard Specification for Wrought Nitrogen Strengthened 11Manganese-17Chromium-3Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29225)
  • ASTM F3141, 2017 Edition, Standard Guide for Total Knee Replacement Loading Profiles
  • ASTM F621, 2012 Edition Reapproved in 2017, Standard Specification for Stainless Steel Forgings for Surgical Implants
  • ASTM F982, Withdrawn with no replacement, Standard Specification for Disclosure of Characteristics of Surgically Implanted Clamps for Carotid Occlusion (Withdrawn 2017)
  • BS ISO 11491, 2017 Edition, Implants for surgery. Determination of impact resistance of ceramic femoral heads for hip joint prostheses
  • BS ISO 13781, 2017 Edition, Implants for surgery. Homopolymers, copolymers and blends on poly(lactide). In vitro degradation testing
  • BS ISO 19213, 2017 Edition, Implants for surgery. Test methods of material for use as a cortical bone model
  • BS ISO 21063, 2017 Edition, Prosthetics and orthotics. Soft orthoses. Uses, functions, classification and description
  • BS ISO 21064, 2017 Edition, Prosthetics and orthotics. Foot orthotics. Uses, functions classification and description
  • BS ISO 21065, 2017 Edition, Prosthetics and orthotics. Terms relating to the treatment and rehabilitation of persons having a lower limb amputation
  • BS ISO 212063, 2017 Edition, Prosthetics and orthotics. Soft orthoses. Uses, functions, classification and description 
  • ISO 13781, 2nd Edition, Implants for surgery - Homopolymers, copolymers and blends on poly(lactide) - In vitro degradation testing
  • ISO 19213, 1st Edition, Implants for surgery - Test methods of material for use as a cortical bone model
  • ISO 21063, 1st Edition, Prosthetics and orthotics - Soft orthoses - Uses, functions, classification and description
  • ISO 21064, 1st Edition, Prosthetics and orthotics - Foot orthotics - Uses, functions classification and description
  • ISO 21065, 1st Edition, Prosthetics and orthotics - Terms relating to the treatment and rehabilitation of persons having a lower limb amputation
  • ASTM F701, Withdrawn with no replacement, Standard Practice for Care and Handling of Neurosurgical Implants and Instruments (Withdrawn 2017)  


For more standards like these, please refer to our Document Center List of Implants for Surgery Standards.